Section-by-Section Analysis
Section 1. Short title. This section would provide that the bill may be cited as the ``Streamlining American Manufacturing Strategy Act''. Section 2. Alignment of timing of updates of strategic plan with updates to National Strategy for Advanced Manufacturing. This section would amend the National Institute of Standards and Technology Act to provide that the strategic plan for Manufacturing USA is updated at least every 4 years, and that the planning cycle for the updates would align with the planning cycle for updates to the National Strategy for Advanced Manufacturing to better ensure the priorities of the national strategy are reflected. This section would also include conforming amendments to update the later statute where it references the strategic plan for Manufacturing USA. Changes in Existing Law In compliance with paragraph 12 of rule XXVI of the Standing Rules of the Senate, changes in existing law made by the bill, as reported, are shown as follows (existing law proposed to be omitted is enclosed in black brackets, new material is printed in italic, existing law in which no change is proposed is shown in roman): NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY ACT * * * * * * * [15 U.S.C. 278s(i)] SEC. 34. MANUFACTURING USA. (a) Definitions.--* * * (b) * * * (c) * * * (d) * * * (e) * * * (f) * * * (g) * * * (h) * * * (i) National Program Office.-- (1) Establishment.--The Secretary shall establish, within the Institute, the National Office of the Manufacturing USA Network (referred to in this section as the National Program Office), which shall oversee and carry out the Program. (2) Functions.--The functions of the National Program Office are-- (A) to oversee the planning, management, and coordination of the Program; (B) to coordinate with and, as appropriate, enter into memorandums of understanding with Federal departments and agencies whose missions contribute to or are affected by advanced manufacturing, including the Department of Agriculture, the Department of Defense, the Department of Education, the Department of Energy, the Department of Labor, the Food and Drug Administration, the National Aeronautics and Space Administration, the National Institutes of Health, and the National Science Foundation, to carry out the purposes set forth under subsection (b)(2); (C) to develop, not later than December 16, 2015, [and update not less frequently than once every 3 years thereafter,] a strategic plan to guide the Program, including a strategy for retaining domestic public benefits from Manufacturing USA institutes once Federal funding has been discontinued; (D) to update the strategic plan developed under subparagraph (C) not less frequently than once every 4 years such that the planning cycle for the updates aligns with the planning cycle for updates to the National Strategy for Advanced Manufacturing required under section 102(c)(4) of the America COMPETES Reauthorization Act of 2010 (42 U.S.C. 6622(c)(4)) to better ensure the Program reflects the priorities of the national strategy; [(D)](E) to establish such procedures, processes, and criteria as may be necessary and appropriate to maximize cooperation and coordinate the activities of the Program with programs and activities of other Federal departments and agencies whose missions contribute to or are affected by advanced manufacturing; [(E)](F) to establish a clearinghouse of public information related to the activities of the Program; [(F)](G) to act as a convener of the Network; [(G)](H) to work with Federal agencies that are not sponsoring or supporting a Manufacturing USA institute to explore and develop options for sponsoring or supporting a Manufacturing USA institute; [(H)](I) to work with Federal agencies that are sponsoring or supporting a Manufacturing USA institute to develop and implement network- wide performance goals with measurable targets and timelines; [(I)](J) to help develop pilot programs that may be implemented by the Manufacturing USA institutes to address specific purposes of the Program, including to accelerate technology transfer to the private sector and to develop entrepreneurship programs; [(J)](K) to provide support services to promote workforce development activities, including the development of industry credentials; [(K)](L) to identify and disseminate best practices for workforce education and training across the Network and further enhance collaboration among Manufacturing USA institutes in developing and implementing such practices; [(L)](M) to collaborate with the Department of Labor, the Department of Education, industry, career and technical education schools, local community colleges, universities, and labor organizations to provide input, as appropriate, for the development of national certifications for advanced manufacturing workforce skills in the technology areas of the Manufacturing USA institutes; and [(M)](N) to coordinate with Manufacturing USA institutes to develop best practices for the membership agreements and coordination of similar project solicitations. (3) Recommendations.--In developing and updating the strategic plan under [paragraph (2)(C)] subparagraphs (C) and (D) of paragraph (2), the Secretary shall solicit recommendations and advice from a wide range of stakeholders, including industry, small and medium- sized manufacturing enterprises, research universities, community colleges, State, Tribal, and local governments, and other relevant organizations and institutions on an ongoing basis. (4) Report to congress.--Upon completion, the Secretary shall transmit the strategic plan required under [paragraph (2)(C)] subparagraph (C) of paragraph (2) and any update to the plan required under subparagraph (D) of such paragraph to the Committee on Commerce, Science, and Transportation of the Senate and the Committee on Science, Space, and Technology of the House of Representatives. (5) Hollings manufacturing extension partnership.-- (A) In general.--The Secretary shall ensure that the National Program Office leverages the capabilities of the Hollings Manufacturing Extension Partnership into Program planning to ensure-- (i) significant outreach to, participation of, and engagement of small- and medium-sized manufacturers in Manufacturing USA institutes across the entirety of the manufacturing supply chain; and (ii) that the results of the Program, including technologies developed by the Program, reach small- and medium-sized manufacturers and that such entities have access to technical assistance, as appropriate, in deploying those technologies. (B) Liaisons.--The Secretary may provide financial assistance to a manufacturing extension center established as part of the Hollings Manufacturing Extension Partnership to support the purposes of the Program by providing services in one or more of the following areas: (i) Support services for small- and medium-sized manufacturers, that many include the designation of a liaison. (ii) Assistance with workforce development. (iii) Technology transfer for small and medium-sized manufacturers. (iv) Such other areas as the Secretary determines appropriate to support the purposes of the Program. (6) Detailees.--Any Federal Government employee may be detailed to the National Program Office without reimbursement. Such detail shall be without interruption or loss of civil service status or privilege. (7) Council for coordination of institutes.-- (A) Council.--The National Program Office shall establish or designate a council of heads of any Manufacturing USA institute receiving Federal funding at any time to foster collaboration between Manufacturing USA institutes. (B) Meetings.--The council established or designated pursuant to subparagraph (A) shall meet not less frequently than twice each year. (C) Duties of the council.--The council established pursuant to subparagraph (A) shall assist the National Program Office in carrying out the functions of the National Program Office under paragraph (2). (j) * * * (k) * * * (l) * * * (m) * * * * * * * * * * [all]